Code table of common errors on Panasonic washing machines

During the process of using Panasonic washing machines , you must have many times encountered the washing machine control panel error message. However, Panasonic washing machine error codes are information that not all consumers understand. Here, WebTech360 would like to send you a list of Panasonic washing machine error codes and the best way to deal with that situation.

Common Panasonic washing machine error codes

Errors that start with the U are usually due to common reasons that users can easily overcome such as not closing the lid carefully, clothes are unevenly distributed in the washing bucket, water source is not strong enough, ...

1. Error code U11 - The washing machine cannot drain

Reason:

- The water discharge pipe is flooded, preventing water from escaping.

- The pipeline is twisted in a certain part.

- The tip of the tube is placed too high compared to the standard level, causing water to be trapped inside.

- The filter slot at the top of the tube attached to the washing machine is clogged

How to fix:

- Check the water drain hose for flooding or not, if there is no kinking.

- Reset the drain hose to low if it is at a higher position than specified.

- Check the water filter slot to see if something is blocking or is blocked with dirt that prevents water from draining.

After doing the above steps, open the lid of the washing machine and close it for normal operation.

You should check the exhaust pipe when you get error code U11.

2. Error code U12 - The washer cover is still open

Reason:

- The washing machine lid is not closed yet.

- Something is stuck in the lid that the machine cannot close tightly.

Remedy: Check that the lid of the machine is not jammed, then close it normally.

Error U12 is usually caused by the lid of the washing machine is not closed.

3. Error code U13 - Unbalanced load detected in the machine

Reason:

- Clothes are not evenly distributed in the washing bucket, causing an imbalance.

- The washing machine is tilted or tilted from the ground.

How to fix:

- Distribute clothes evenly in the washing bucket.

- Adjust the washing machine so that it is level on the floor then open the lid and close for the machine to operate.

Check and adjust the machine if the machine is deviated from the floor.

4. Error code U14 - The washing machine is not supplied with water

Reason:

- The water source is not strong enough, the water pressure is too weak.

- The water tap may not be open, so water cannot lead to the washing machine.

- The water filter may be blocked due to dirt or stuck by something.

How to fix:

- Check the water pressure again, if the water pressure is not strong enough, you can use an automatic booster pump.

- Check whether the water tap is open or not.

- Check the filter for any jam or not, then clean the strainer to get rid of the dirt blocking the water flow.

Check the water supply system again when there is error code U14.

5. Error code U99 - Child safe mode

Cause: When the Panasonic washing machine has been activated in child safety mode but the lid is opened for more than 10 seconds, the washing machine will automatically drain the water out, and at the same time stop the entire washing cycle.

Remedy: Restart the machine by unplugging and re-plugging it in 5-10 seconds.

Child safety mode will stop the machine from operating when the lid is left open for more than 10 seconds.

Technical error code table of Panasonic washing machine

In general, Panasonic washing machine error codes prefixed with H are errors originating from the hardware or the internal controller. These errors range from moderate to severe, making it difficult to fix quickly. Error codes that begin with an H include:

- H01: Pressure sensor defective or damaged.

- H04: A short circuit occurs in the electrical system.

- H05: Hardware error caused the washing machine to not be supplied with water.

- H07: Engine defective.

- H09: Communication error between controller and display board.

- H17: Temperature sensor error.

- H18: Motor is rotating or there is a problem in the clutch shaft.

- H21: Pressure sensor defective.

- H23: The relay on the printed circuit is overheated.

- H27: The washing bucket is punctured, causing water to leak, the drain valve is stuck.

- H28: Cooling fan is running slowly, because the power supply has a voltage drop.

- H41: 3D sensor cannot transmit data to the central controller.

- H43: The washing machine was found to have an electrical leak.

- H46: Occurrence of abnormal signal on the unit. This error can be caused by the sensor base or the electronic controller.

- H51: Engine overloaded, transmission system malfunction.

- H52: The input voltage is higher than the working voltage of the washing machine.

- H53: Input voltage is too low, causing the machine to not have enough voltage to operate normally.

- H55: Main drive motor is damaged, needs to be replaced.

When you encounter error codes beginning with letter H, you should contact customer service to get the support of specialists. Because the repair of hardware-related problems will require specialized tools and certain knowledge and knowledge that not all consumers have.

>> See also:  Washing is no longer a hassle with Panasonic washing machines

In this case, you should unplug and wait for the assistance of a technician.

The best selling Panasonic washing machine products today:

The above article mentioned the Panasonic washing machine error codes commonly encountered in most of Panasonic's models and how to fix them. Hopefully the above sharing will help you use your Panasonic washing machine more effectively.